CPC中文印刷社区

CPC中文印刷社区 (https://www.cnprint.org/bbs/index.php)
-   ◆- 数码印刷综合讨论区 (https://www.cnprint.org/bbs/forumdisplay.php?f=109)
-   -   施乐D110的问题,求大神相助 (https://www.cnprint.org/bbs/showthread.php?t=270406)

xsd2016 2016-11-15 10:30

施乐D110的问题,求大神相助
 
施乐 D110 出现代码012-250,怎么解决啊,新手。

精正 2016-11-15 11:11

D110二手机现在是什么价格啊?

xsd2016 2016-11-15 15:37

引用:

作者: 精正 (帖子 2154932)
D110二手机现在是什么价格啊?

不知道啊,我们这台买了很久了,我刚刚接手机器维护。

balenofeng 2016-11-15 22:33

012-250 End Guide Motor 1 Start Fail
Bsd-on:CH15.19

When the End Guide is moving away from the home position, the End Guide Home Sensor 1 does not turn OFF within the specified time after the End Guide Motor 1 On.

Procedure
Enter the Diag Mode, input DC330[013-121] (End Guide Home Sensor 1) and turn it ON. Turn the sensor ON and OFF with a sheet of paper.

Does the display switch between ’H’ and ’L’?
Yes No

Go to 2.2.3.2 Permeable Sensor Failure FIP and fix the End Guide Home Sensor 1.

Press the Stop button.

Input either DC330[013-029] (Up) or [013-030] (Down) (End Guide Motor 1) and turn it ON.

Does the End Guide Home Motor 1 operate?
Yes No

Is the CR1 on the Folder PWB ON?
Yes No

Refer to BSD CH15.2 and check the +5VDC circuit to the Folder PWB J8140-4.

Is the voltage between the Folder PWB J8137-2 (+) and the GND (-) +24VDC?
Yes No

Refer to BSD CH15.5 and check the +24VDC INTLK circuit to the Folder PWB J8137-2.

Turn OFF the power, disconnect connector J8138 from the Folder PWB.

Measure the wire wound resistance of the Motor.

Between J8138 pin-7 and each of pin-8/10

Between J8138 pin-9 and each of pin-12/14

Are the resistances approx. 4.6 Ohm for each?
Yes No

Check the following connections for open circuits and poor contacts. If no problems are found, replace the End Guide Motor 1 (PL 25.69)

Between J8138-7 and J8142-2

Between J8138-8 and J8142-3

Between J8138-9 and J8142-5

Between J8138-10 and J8142-1

Between J8138-12 and J8142-4

Between J8138-14 and J8142-6

Between Finisher PWB J8010-6 and Folder PWB J8139-14

Between Finisher PWB J8010-7 and Folder PWB J8139-13

Between Finisher PWB J8010-8 and Folder PWB J8139-12

Between Finisher PWB J8010-9 and Folder PWB J8139-11

Check the following connections for open circuits and poor contacts. If no problems are found, replace the Folder PWB (PL 25.68), followed by the Finisher PWB (PL 25.3).

Between Finisher PWB J8010-6 and Folder PWB J8139-14

Between Finisher PWB J8010-7 and Folder PWB J8139-13

Between Finisher PWB J8010-8 and Folder PWB J8139-12

Between Finisher PWB J8010-9 and Folder PWB J8139-11

Check the following. If no problems are found, replace the Folder PWB (PL 25.68), followed by the Finisher PWB (PL 25.3).

The End Guide Motor 1 gear for wear and damage

The Drive Belt for improper tension, wear, and damage

The Sensor Actuator for failure

xsd2016 2016-11-16 12:26

引用:

作者: balenofeng (帖子 2155235)
012-250 End Guide Motor 1 Start Fail
Bsd-on:CH15.19

When the End Guide is moving away from the home position, the End Guide Home Sensor 1 does not turn OFF within the specified time after the End Guide Motor 1 On.

Procedure
Enter the Diag Mode, input DC330[013-121] (End Guide Home Sensor 1) and turn it ON. Turn the sensor ON and OFF with a sheet of paper.

Does the display switch between ’H’ and ’L’?
Yes No

Go to 2.2.3.2 Permeable Sensor Failure FIP and fix the End Guide Home Sensor 1.

Press the Stop button.

Input either DC330[013-029] (Up) or [013-030] (Down) (End Guide Motor 1) and...

:big_smile:这叫我如何是好?人家看英文是读句子,我是看单词


所有时间均为 +8, 现在的时间是 2025-07-06 23:35.

Powered by vBulletin® Version 3.8.12 by vBS
Copyright ©2000 - 2025, vBulletin Solutions, Inc.